Trending December 2023 # We Couldn’t Create A New Partition Error 0X9Cfc7550 During Windows Setup # Suggested January 2024 # Top 12 Popular

You are reading the article We Couldn’t Create A New Partition Error 0X9Cfc7550 During Windows Setup updated in December 2023 on the website Kientrucdochoi.com. We hope that the information we have shared is helpful to you. If you find the content interesting and meaningful, please share it with your friends and continue to follow and support us for the latest updates. Suggested January 2024 We Couldn’t Create A New Partition Error 0X9Cfc7550 During Windows Setup

If you’re encountering We couldn’t create a new partition error message on your Windows computer while installing Windows 11/10, then the solution we will present in this post is intended to help you remediate this issue.

This error might happen for any number of reasons, even on perfectly functioning SSDs and HDDs.

We couldn’t create a new partition, Errror 0x9cfc7550

If you’re faced with this issue during Windows Setup, you can try our recommended solutions below and see if that helps to resolve the issue.

Disconnect additional Hard Drives, USB drives, and Memory cards

Create a new partition using DiskPart

Set the intended Windows Install partition as primary/active

Use USB 2.0 Drive.

Let’s take a look at the description of the process involved concerning each of the listed solutions.

1] Disconnect additional Hard Drives, USB drives and Memory cards

When using multiple hard drives, the first and foremost thing to do is disconnect all hard drives except the primary hard drive where you install Windows. Once you disconnect all your other hard drive(s), try to install Windows again and see if you can proceed with the installation without encountering the error.

Also, other than the actual Windows 10 bootable USB drive, if you have any other USB drives and memory cards connected to your system, then on rare occasions Windows might confuse these drives for regular hard drives. Disconnect those additional USB drives or memory cards and try installing Windows again.

2] Create a new partition using DiskPart

This solution will delete all files on your selected hard drive, so use it on a new computer that doesn’t have any files on it, or only if you have a backup available.

To run DiskPart, do the following:

Start Windows 10 setup using bootable USB or DVD.

Choose Advanced tools and then select Command Prompt.

When Command Prompt opens, enter the following command:

start diskpart

Now enter the following command:

list disk

You should see the list of all hard drives connected to your computer.

Find the number that represents your hard drive and enter the command below and be sure to replace 0 with a number that matches your hard drive.

select disk 0

Next, input the following lines and press Enter after each line:

disk 0 clean disk 0 create partition primary disk 0 active disk 0 format fs=ntfs quick disk 0 assign

After running the commands, type exit and hit Enter to close Command Prompt.

Start the installation process again and see if it completes successfully. If not, try the next solution.

3] Set the intended Windows Install partition as primary/active

You might encounter this error if the partition you are trying to install Windows 10 is not active. To make a partition active, you need to have access to the command prompt.

Do the following:

Start DiskPart as shown above.

Next, type the command below and hit Enter

list disk

You should see the list of available hard drives.

Locate your hard drive and enter the command below and be sure to replace 0 with a number that represents your hard drive.

select disk 0

Next, type the command below and hit Enter

list partition

The list of available partitions will appear.

Now, locate the partition on which you want to install Windows 10 and type the command below and hit Enter. Replace 1 with a number that matches your partition.

select partition 1

Lastly, type the command below and hit Enter to set the partition as primary/active.

Active

Type exit and press Enter to exit the Command Prompt.

Start the installation process again and check if the problem is resolved. Otherwise, continue with the next solution.

Read: Windows Setup couldn’t create a new partition or locate an existing one

4] Use USB 2.0 Drive

If you are using a USB 3.0 bootable drive to install Windows, then it might also be a reason why Windows is giving you this specific error. To solve it you can try using a USB 2.0 drive.

Hope this helps!

You're reading We Couldn’t Create A New Partition Error 0X9Cfc7550 During Windows Setup

How To Create A Partition On Your Mac

Unlike Windows-based computers, Macs usually do not come with multiple hard-drive partitions. It is just a single partition that you see when you first boot your Mac. Though there is no harm using your Mac with a single partition, it is highly recommended that you have at least two partitions on your machine. This will let you store your important files on one partition when the other one is being formatted. It is also helpful if you plan to install another OS beside your Mac OS. Regardless of your reasons, here’s how you can do it.

Creating a Partition on a Mac

It is really easy to create a partition on a Mac, as your Mac comes preloaded with an utility that allows you to do that. The utility we are talking about is called “Disk Utility” which is found in the Utilities folder on your Mac. Besides partitioning, it allows you to perform a number of disk-related operations on your machine.

Here are the steps you need to follow:

Name – Enter a name for your new partition, it could be anything of your choice. It’s suggested that you use a meaningful name, though.

Format – This one is important. Make sure to choose the appropriate format that you think will work with the files that you will be storing on this new partition.

Size – Specify the size for your new partition.

7. Restart your Mac when it is done.

Congrats! A new partition has been successfully created on your Mac, with all of your defined settings. You can now use it to store your files, videos, music, and all the content that you have been storing on your main hard drive until now.

Conclusion

While it’s easy to use a Mac with just a single partition, adding another one decreases the chances of your files being corrupted in case you crash your machine.

Mahesh Makvana

Mahesh Makvana is a freelance tech writer who’s written thousands of posts about various tech topics on various sites. He specializes in writing about Windows, Mac, iOS, and Android tech posts. He’s been into the field for last eight years and hasn’t spent a single day without tinkering around his devices.

Subscribe to our newsletter!

Our latest tutorials delivered straight to your inbox

By signing up, you agree to our Privacy Policy and European users agree to the data transfer policy. We will not share your data and you can unsubscribe at any time.

Cannot Create New Storage Space, Error (0X00000057), The Parameter Is Incorrect

Windows Storage Space is a feature in Windows 10 which allows you to take a backup of files in case of a drive failure. However, if you are getting an issue with the message “Error (0x00000057): The parameter is incorrect with storage space“, then in this post, we will share a solution for this. The error appeared in Windows 11/10 and is a known bug that has been acknowledged as a bug by the Microsoft Team.

Cannot create new Storage Space, Error (0x00000057), The parameter is incorrect

The error occurs when a user tries to create a new storage space into an existing pool or when creating a new pool so they can retain the extra copies. The complete error message goes as:

The graphical interface for managing Storage Spaces in Windows fails when creating a storage pool with another error “Can’t prepare drives – the parameter is incorrect”.

The same error was reported in the Reddit forum as well. The user shared his experience, where he noticed the contents of some of the files went corrupt. It happened after upgrading Windows. When the CDKDSK tool was used, it reported more problems with a resulting message saying.

File record segment 67C08 is an orphan.

There are a couple of workarounds which may not sound very nice, but that’s the solution for now.

Storage Spaces problem – How to Restore corrupt files?

Before you begin, remember to create a system restore point first, so that you can always revert should things not go as expected.

1] Restore from an older backup

The best method is to restore from a week old back or a day earlier before you upgraded to the Windows 10 feature update. It will make sure there is no inconsistency among the files. Always make sure to run the CHKDSK tool to check for any inconsistency.

It is also recommended to lock the parity drive to read-only mode for now. If you’re restoring your images to your parity drive, that’ll probably keep introducing more corruption as you make changes.

2] Run CHKDSK tool

CHKDSK tool checks the file system and file system metadata of a volume for logical and physical errors. So once you run it, the file system will become consistent again, but you will have to manually check if the data after the check is incorrect or not.

How to create new Storage Space using PowerShell

Windows PowerShell offers cmdlets that can create new Storage Space. So until the interface is fixed, you can follow this method. As a warning, you should have a clear understanding of what you are doing here and execute the commands correctly. Since we will not delete anything, the existing storage space is safe. These are the three things you need to use the commands.

Storage pool name

Disks to use to create the pool

Storage subsystem or Storage Spaces

Here is the script you can execute on PowerShell. The first line uses the **Get-PhysicalDisk** cmdlet to get all PhysicalDisk objects than are not yet in a (concrete) storage pool and assigns the array of objects to the $PhysicalDisks variable. The second line creates a new storage pool using the $PhysicalDisks variable to specify the disks to include from the WindowsStorage subsystem.

$PhysicalDisks = (Get-PhysicalDisk -CanPool $True) New-StoragePool -FriendlyName CompanyData -StorageSubsystemFriendlyName "Windows Storage*" -PhysicalDisks $PhysicalDisks

You will have to launch PowerShell with Admin permission and an admin account to execute the commands.

So until you keep facing the issue and Microsoft rolls out a fix, use this command to create a new pool. Also, make sure to keep the backup as read-only.

I hope you were able to resolve this error 0x00000057.

Fix: Formatted Wrong Partition In Windows 10/11

Fix: Formatted Wrong Partition in Windows 10/11

976

INSTALL BY CLICKING THE DOWNLOAD FILE

Try Outbyte Driver Updater to resolve driver issues entirely:

This software will simplify the process by both searching and updating your drivers to prevent various malfunctions and enhance your PC stability. Check all your drivers now in 3 easy steps:

Download Outbyte Driver Updater.

Launch it on your PC to find all the problematic drivers.

OutByte Driver Updater has been downloaded by

readers this month.

What to do if I have formatted the wrong drive partition in Windows 10, 8.1?

There are some useful applications that you can install in order to bring back your important data in Windows 8.1 or Windows 10 that you previously lost to the partition format action you made by mistake. Some of them you can get for free and some of them cost just a few dollars so mainly if you have very important data that you need to get back I don’t think a few dollars can stand in your way.

How to get back your partition if you formatted it by mistake in Windows 8.1 or Windows 10 1. Use Remo Software

Note: This application will restore most of your files including videos, documents, music, emails, files and many others.

Download here “remo Software”

Now, wait for the download to complete.

Note: Install it where the default path is in the installation process.

After the installation process is completed you can go on your Windows desktop and run the icon from there.

After you open the application you should have in front of you the main page.

You will have a list of available drives that you can recover data from.

After you start the process you will have to wait a couple of minutes (approximately 25 minutes)

Note2: As a safety precaution it is recommended to always make a backup copy of the system before you attempt to format a partition or a full drive.

2. Use iCare Data Recovery

Download here iCare Data Recovery standard

Note: This application is free

Install the application on a different partition then the one you formatted.

After the installation is completed you will need to go on the desktop and open ” iCare Data Recovery” icon.

After the scanning device process is finished you will have the formatted partition there.

Note: After you selected “Show Files” feature you will have in front of you the files that were on your partition before you formatted it.

You only have to save the files that you lost to another partition on the Windows 8.1 or Windows 10 device and you are all done.

3. Use other partition software

The tools presented below work well on Windows 10, 8.1 but you might know other partition software that you have used already. Some of them like MiniTool Partition Wizard, Paragon Partition Manager or EaseUS Partition are known worldwide and will help you. However, before downloading one of them, be sure that they have a backup feature so you can recover your wrong formatted drive.

Expert tip:

There you go; two quick methods on how to get back your lost data if you formatted the wrong partition in Windows 8.1 or Windows 10. Please write us below for any additional questions you may have on this subject and we will help you further with this issue as soon as possible.

READ ALSO: Microsoft to Discuss Windows 10 on Tablets and Phones Next Week at a Special Event

Still experiencing troubles? Fix them with this tool:

How To Easily Automount Windows Ntfs Partition In Ubuntu

One way to automount NTFS drive is by editing fstab, but that might not be simple for beginner Linux users. An alternative way is to use a GUI tool named ntfs-config.

Open the terminal ( Ctrl+Alt+T ) and use the following command to install the tool:

sudo

apt-get install

ntfs-config

Alternatively, you can install it from Ubuntu Software Center.

Before using, we need to tweak the tool a bit as there is a known bug which stops the tool from working properly. It looks for a directory which needs to be created. In the terminal, use the following command to create the mentioned directory:

sudo

mkdir

-p

etc

hal

fdi

policy

Now we are ready to use the ntfs-config tool. Launch ntfs-config. Remember, it needs administrative rights to run the tool. When you start the tool, it lists all the partitions that are available on your computer. The interface looks like this:

By the way, in case you do not know which drive is numbered what (i.e. /dev/sdaX which is not similar to Windows naming convention of drives), you can use the following command in terminal to find it out.

sudo

fdisk

-l

which outputs (for my computer) like this:

Device Boot Start End Blocks Id System

dev

sda1

2048

206847

102400

HPFS

NTFS

exFAT

dev

sda2

206848

215541759

107667456

HPFS

NTFS

exFAT

dev

sda3

215544166

625141759

204798797

f W95 Ext

(

LBA

)

dev

sda5

215544168

420340724

102398278

HPFS

NTFS

exFAT

dev

sda6

420340788

504296414

41977813

HPFS

NTFS

exFAT

dev

sda7

535547904

545062911

4757504

Linux swap

Solaris

dev

sda8

545064960

625141759

40038400

Linux

dev

sda9

504297472

529539071

12620800

Linux

dev

sda10

529541120

535543807

3001344

Linux swap

Solaris

In the output, look for the column Blocks. This gives the size of the partition in bytes. In the example above, 102398278 bytes can roughly be estimated as 102 GB.

Once you select the mount point, it gives you option of enabling write support for the drives. Its up to you if you want this feature.

Save and close and you are done with a reboot. You will find your drive(s) automatically mounted at the start-up.

Abhishek Prakash

Abhishek is a Linux lover and Opens Source enthusiast. He takes a keen interest in day-to-day computer life and wishes to share his experience with others to make their computer experience better and easier. He is the owner of increasingly popular tech blog Computer And You and Open Source blog It’s FOSS.

Subscribe to our newsletter!

Our latest tutorials delivered straight to your inbox

By signing up, you agree to our Privacy Policy and European users agree to the data transfer policy. We will not share your data and you can unsubscribe at any time.

5 Ways For New Businesses To Create A Stellar And Enduring Brand

Branding is indispensable for businesses, big or small, new or old

Branding defines a business’s identity; it is how a business presents itself to the world.

But branding is much more than fancy logos and catchy taglines – it captures the ethos of a business and guides its journey.

Let’s look at some ways to transform a new business into a trustworthy and successful brand.

Download our Premium Resource – Brand vision and identity playbook

Access the Successful SEO guide

But first, what’s your story?

It all begins with the narrative.

A cancer survivor launches a line of green juices. A former drug addict launches a life-coaching business to help others overcome similar obstacles. A former ‘slacker’ is now known as a “multi-passionate entrepreneur” with a penchant for transforming lives and businesses.

Everyone has a story to tell. What the successful brands do is find a way to leverage theirs. People don’t set up businesses just to make money anymore. There is usually a larger purpose behind it. What is yours?

Your story and your purpose will define your brand voice

Together, they will guide the content you create

They will determine the kind of audience you attract

They will determine the communication channels you pursue

Your story drives your message. It gives your brand credibility and a unique voice, and essentially it positions it. Before you can begin branding in earnest, you must figure out your story and how to best share it with the world.

1. Align your online presence with the story

The story and the message are an essential part of brand building, but still only a part of it. To become a brand, a business needs to pay attention to the tangible elements as well – such as graphics, aesthetics, and content.

Once you have launched a business, everything that you do around it – how you make the website, how you write the web copy (or the voice you infuse it with), how you position the content, and the way you interact on social – must vibe with the essence of your story, which is now the essence of your business. This helps a business to solidify its identity.

Branding elements include the color scheme on the website; the design of the logo; the tone and tenor of the content – written, audio, or visual; the tone and tenor of the microcontent (the posts you make on social platforms); the design or color scheme of the merchandise; the design and colors of the physical store (if you have one); and the aesthetic appearance of the business at promotional events.

To cultivate a brand identity, all the elements – tangible as well as intangible – must work together and in a consistent manner.

2. Create a company culture around brand ethos

The mission of a business informs its brand values. These need to percolate down to the latest employee hired by a company. Everyone on the team needs to be aware of and share the brand ethos. They also need to demonstrate that through their behavior, particularly those in customer-facing roles.

What experience do you want your customers to take away after doing business with you? How can you make this experience more memorable? Focus on the ideal customer experience and reverse engineer to make it happen.

3.. Create innovative content that pulls in right people

With the right content your business can:

Reach out to the target audience and beyond

Build a followership

Build a relationship with the followership

Keep the engagement going

Present yourself the way you want

But content can only do the above if it is innovative. Content glut is a real phenomenon and consumers have little-to-no patience for businesses that engage in product-specific marketing instead of customer-oriented marketing.

Fortunately, it has never been easier to create eye-catching content, though trial and error is inevitable here. While the audio-visual format is a universal hit, it might or might not work for your business. Every business needs to figure out the best way it can tell its story and reach the intended people with the message. And though the video is wildly popular as a means of content consumption, the written word has its dedicated fans, too. Podcasts are rising in popularity as well.

Two most important things to consider: what format can you best create the content in, and is this the format that your ideal audience prefers?

4. Change the way you look at social media

Social media is about give and take. In fact, it’s mostly about give, give, give, and then some take.

Shift the focus from what you can get out of the popular social platforms – i.e. a ton of followers, to what you can give and are giving right now – i.e. great content and user experience for free. Spread the word, generate engagement. When your content is top-notch and distribution generous, people will notice it, appreciate it, and follow it.

5. Seek collaborations with industry influencers

This is the fastest way for businesses to reach new and relevant segments. In fact, so effective is this tactic that last year “companies spent more than $1billion on influencer marketing.”

Seek out influencers who share similar values and discuss opportunities to work together. When you feature in their videos or Instagram posts, you gain exposure to not just their followers but also all those whom the followers share the posts with. Your reach goes through the roof.

As a brand, you are out there, in front of hundreds of thousands of potential customers. And by aligning with the right kind of influencers you are also in the right company. You have sent a strong message about who you are and where you stand.

Branding is more than skin deep

Branding is a fun and creative way of carving out a distinct identity in a noisy and crowded marketplace. An identity that attracts the right kind of customers and translates into stronger business relationships. How do you handle the branding challenges of your business?

Update the detailed information about We Couldn’t Create A New Partition Error 0X9Cfc7550 During Windows Setup on the Kientrucdochoi.com website. We hope the article's content will meet your needs, and we will regularly update the information to provide you with the fastest and most accurate information. Have a great day!